Security

The JA-65X digital communicator is designed for JA-63 and JA-65 alarm control panels. If the 65X module is installed, the control panel can communicate with a Monitoring Station, send voice messages, SMS messages and dial a numeric Pager as well as communicate with a remote PC. A standard analog telephone line (type TNV 1-3) must be connected to the module for these functions.

The GD-04D allows relay X and Y control by entering numeric codes (DTMF codes) on the telephone keypad during calls. The DTMF codes intended for use have to be programmed.

ESIM264 is an Alarm and Control System (GSM Caller) for the security of premises and control or management of electronic devices through GSM network. The basic advantage of the GSM system is the user’s ability to know immediately what’s happening at their home, apartment, warehouse, summer house or other premises even when the user himself is a long way away – in another city or even in another country. It also has a remote control switch to turn on or turn off 4 or more different devices just by sending SMS messages.

• System can be armed and disarmed in one of three ways: via keypad EKB3, key iButton® or free-of-chage call from your phone;
• ESIM264 supports the CONTACT ID protocol which is required to transmit signals to a Monitoring Station;
• ELDES wireless devices can be added to the system using the EWT1 module. This increases the maximum number of Zones to 44 units and the maximum number of Outputs to 44 units;
• Automatic Output control – the system may enable / disable individual Outputs automatically when a specified event occurs;
• Fault reporting: The system automatically reports if any of the sensors or sirens disconnect from the system;
• Battery check option - checks the health of the battery and reports when the battery needs to be replaced;

The JA-82KRC is a basic configuration of the JA-82K control panel. The JA 82K main board provides building-block-like modularity which allows functional extensions to be made by simply plugging-in the required modules.

PIR sensor EWP1 is a wireless device with integrated motion detector for use as part of the ELDES wireless security system. The sensor allow expanding security zones administrated by the systems up to 16 additional zones and also the installation is comfortable and simple as it does not require any wired connections between the system devices. The user only needs to turn on the required number of PIR sensors EWP1 and connect them to the control panel, either by sending a command via SMS message or using the ELDES Configuration Tool software.

The MCT-302 is a fully supervised PowerCode™ magnetic contact transmitter, designed primarily for protecting doors and windows using a built-in magnetic contact that operates in conjunction with a magnet to detect the opening and closure of a door or window. This highly reliable top-performance wireless device is easy to install and operate in a wide range of residential and commercial environments.

The AJAX Socket is a smart power plug for full control of your devices. The Socket can help prevent damage in the event of power surges, but it is mainly used to save energy and automate standard tasks. The Socket simply plugs between your current plug and your wall socket, and then you are able to use the Ajax App. thousands of miles from home to turn on your lights, manage devices, monitor power consumption, etcetera. Especially for hot water boilers this is very interesting. If you forgot to remove the plug of the boiler after departure, that’s no longer a problem. Curious how much power a certain device costs? With this Socket you can read it exactly. Also ideal when renting out houses, you can track exactly how much electricity your guests use.

The Universal GSM module is easy to connect (install) with your HomeGuard or other PSTN alarm panels, by inserting a telephone wire in both analogue inputs. The GSM module enables the control panel to communicate via cellular networks.
The modem translates the analogue signals and converts them into a GSM signal. A SIM card (prepaid or subscription from any provider) has to be placed inside the GSM module.
The GSM module creates a two-way communication. This enables your security system to send an alarm alert to your mobile phone in cause of an emergency, and makes it possible to monitor and control your security system remotely.
This model is supplied with an E-plug.

Alarm system that includes: Gateway, 2 Door / Window sensors, 1 motion sensor and a remote control. The gateway connects to an RJ-45 ethernet network and has internal siren and backup battery. Up to 4 Kodak security cameras and 32 sensors can be connected.

The detector is used for human motion detection in the interior of a building. Thanks to the combination of motion and microwave detection, the detector is highly resistant to false alarms.
The detector guards the same way as a classic PIR motion detector.
When motion is sensed in the guarded area, the MW detector is activated to confirm the triggering of the PIR. Only after receiving a confirmed alarm signal from the MW unit, does the detector send an alarm report to the control panel.

The JA-80L is a component of Jablotron’s Oasis 80 alarm system. It can be used as the following:

• An indoor alarm siren;
• A wireless door bell;
• A detector-triggered chime;
• A sounder for entrance and exit delay beeps;
• Thief verification;

The JA-60V is an outdoor intruder detector designed to detect human body movement in a protected area.

The MCM-140/MCM-140+ is a wireless remote control unit for the PowerMax family control panels. The MCM-140 and MCM-140+ differ in their transmitted ID type and functions.
1The MCM-140/MCM-140+ enables the user to arm/disarm the alarm system, to initiate emergency/fire/panic alarms, to perform one of the AUX (auxiliary) functions (see Note 2 and 3 in Section 7), to turn lighting devices on and off, and PGM control. The keypad includes an RF transmitter that sends out a differently coded RF signal for each command.
For PowerMax, the MCM-140 enables activation of the Aux (Auxiliary), seven home control outputs (X-10), one PGM output, Fire and Emergency functions. Each button needs to be individually defined for the AUX, PGM or X-10 functions at the corresponding points of the define panel and define outputs menu of the control panel.

The RC-88 is designed to be a remote control for setting/unsetting (arming/disarming) an alarm system, triggering panic alarms or remotely controlling other appliances. The battery-powered wireless button communicates via OASIS radio protocol.

Get warned by flooding and intervene to prevent against water damage. The ebode water detector is battery operated and provided with 2 sensors which have to be placed on the location where water will be expected. When detecting water or moisture the eWD18 will sound an alarm (85DB), like a smoke detector does as a stand-alone system. To register the eWD18 to an X-10 network (BS800 HomeGuard, SC-28 Homeprotector/ProtectorPlus BS880/4 and BS880/7), the water detector is part of your X10 security system and here an alarm message will also be given.

The MCT-501 is a fully supervised digital glass-break wireless detector compatible with PowerMax™ and other Visonic PowerCode™ wireless systems. It is designed for a wide range of residential and commercial applications where reliable glass-break detection is required.
The MCT-501 employs an advanced patented acoustic pattern recognition technology that can reliably distinguish between true alarms and false alarms. It provides 360o detection range of up to 6m (20 ft) and can detect breaking of different types of glass including plate, tampered, laminated and wired.

Adjustable bracket for EL-2645 and EL-1100 wireless motion detectors.

The MCT-220 enables people, for example senior citizens in their home environment, to transmit an emergency call when they are at some distance from their communication unit.

The detector indicates room water floods (e.g. cellars, bathrooms). This information is sent to an alarm system for alert message transmission. It is connectible to an Oasis alarm system via a JA-81M wireless detector. Plug it into the IN1 input terminal (red wire) and GND (black wire). If the detector is triggered (e.g. by a water), it sends a trigger signal. If the detector goes into a stand-by condition, it sends a non-triggered signal. The LD-81 takes its power supply from the JA-81M´s circuit.
It is possible to use the LD-81 with an older type of detector, the JA-60N, for Profi systems if you insert a 4k7 resistor in series with the LD-81 between the INP (red wire) input terminals and GND (black wire).

EPIR is a security alarm system that works with GSM network.

Alarm system ELDES EPIR supports CONTACT ID protocol which is required to transmit signals to Monitoring station.

ELDES EPIR868 (ELDES EPIR version with installed 868 MHz radio transmitter-receiver) can operate as an access point for wireless ELDES devices.

The system DZEUS is a micro-processor device used to remotely observe and control cars, motorbikes and other vehicles through GSM network.

GSM-350 is a cellular communication module that connects some of the PowerMax® systems to the alarm central station. The module can report via GPRS* data channel and/or through the GSM network. This enables a high-speed and highly-reliable communication channel in cases of line failure or tampering with the standard telephony lines.

In addition, it supports remote operation and event reporting via SMS. For any property without land-based telephone lines, the GSM-350 is a must-have. It extends the control panel functionality to any site, such as homes with VoIP-based telephony, anchored boats and isolated vacation houses.

The module is internal and fits in the PowerMax system, so no additional external elements are needed. The integrity of the backup communication channel is ensured through continuous monitoring.

Tens of detectors and kilometers of wire can now effortlessly be transformed into a modern smartphone-controlled security system. Replacing the old security central unit, the module connects wired devices to a hub and makes them a full-fledged part of Ajax. MultiTransmitter is a step towards awareness and reliability. For a security company, it opens the possibility to configure the equipment remotely, and users get all the benefits of managing the system through an app.

The JA-83K control panel is a modular unit, with 50 addresses (marked 01 to 50). The heart of the unit is the JA-83K main board with 10 wired inputs (up to 30 using JA-82C modules).

This type of acustic indicator is 12VDC powwered and can be used as a powerful indoor siren.

4,8V 1800mAh rechargeable NiCd battery to be used with the OS-36x wired sirens.

The detector provides an analysis of environmental conditions through the entire movement speed frequency spectrum, allowing focus on intruders and eliminating environmental factors of false alarms. The spectrum analysis is embedded in the VLSI based electronics of the detector assuring high reliability and trouble free operation.
As the LC-104-PIMW-W is a combined technology (PIR & microwave) an alarm signal relay activation occurs only when signals from both sensors (PIR & MW) are present at the same time. The effective detection range is the range of which the patterns (PIR & MW) are intersected. The GAIN potentiometer adjustment changes the MW signal intensity so that the effective pattern will be scaled.

EPIR is a security alarm system that works with GSM network.

Advanced Internet-based Home Control Solution for PowerMaxPro

Visonic’s PowerLink is the most comprehensive Internet-based solution for advanced home security and control. It enables alarm central stations, security service providers and homeowners to leverage the full power of Internet connectivity to take their home security, safety and automation to the next level.

At the most basic, PowerLink offers a plug and play broadband IP event notification solution. And, with connection to up to 14 cameras placed around the premises, PowerLink can expand to an IP-based video alarm verification solution offering smart recording and fast forwarding of events to the alarm central station.

IP-based Event Notifications

With more and more homeowners moving to VoIP communications, leaving behind PSTN lines, broadband becomes an ideal method for cost-free alarm event notifications delivery to central stations. Visonic's PowerLink Internet-based home control and surveillance system features built-in IP-based event notification capabilities. By simply plugging the PowerLink system into a free port on the home router, the alarm system is connected to the IP receiver at the central station – with no need to configure the system or the router. This provides a true plug and play experience for both the security installer and alarm central station. In addition, PowerLink provides a rapid supervision mechanism, enabling the central station to enjoy commercial-grade line supervision to all connected home security systems at zero cost.

Utilizing PowerLink as an IP-based event notification solution requires that Visonic's IPMP (IP Management Platform) be implemented as an IP receiver at the central station.

Image Alarm Verification the Right Way

As PowerLink is fully integrated with the PowerMax® home security system, it has the ability to send alarm time images based on real motion detection, which significantly reduces the cost to service providers and hassle to homeowners of false alarms.

The system enables central stations to receive image alarm verification information within seconds of the alarm time compared to the several minutes it takes with GPRS or PSTN-based alarm verification solutions. Moreover, alarm time images can be forwarded to the homeowner's email or mobile phone for immediate view and verification. By the time the security service provider calls, the homeowner already knows if the person that activated the alarm is authorized to be there or is an intruder. This means that the police or a central station guard is sent to the premises only when truly necessary.

Enhanced Consumer Web Services

PowerLink is not only a broadband event notification solution but a full-grade service platform that enables service providers to offer enhanced, web-based security and surveillance services to their customers. Homeowners can login to the secure PowerLink web portal, accessible from all standard PC and mobile phone browsers, and via an easy-to-use interface control their home security system, view its status, control X-10 compliant home devices and view live and alarm time recorded video from wireless and wired IP cameras. In addition, homeowners can set up the system to notify them by email or mobile phone text message whenever security, home devices or camera events occur.

Total Control PowerLink is offered with the Visonic IPMP - IP Management Platform. The IPMP serves as an IP receiver in alarm central stations as well as a full grade service platform for consumer web services. By implementing the IPMP, service providers gain full control over the PowerLink service, including account and service management, billing, messaging, and much more.

Tens of detectors and kilometers of wire can now effortlessly be transformed into a modern smartphone-controlled security system. Replacing the old security central unit, the module connects wired devices to a hub and makes them a full-fledged part of Ajax. MultiTransmitter is a step towards awareness and reliability. For a security company, it opens the possibility to configure the equipment remotely, and users get all the benefits of managing the system through an app.

The JA-82KRG is a configuration of the JA-82K control panel with the JA-82R 868MHz RF communications module and the JA-80Y GSM comunicator.
The JA 82K main board provides building-block-like modularity which allows functional extensions to be made by simply plugging-in the required modules.

The JA-88P wireless PIR detector is designed to indicate disturbance outside the building caused by human bodies. It is a two-zone outdoor detector by Optex supplemented with a transmitter compatible with JA-80 OASiS systems. Both the detector and the transmitter are powered by three lithium batteries. Both devices have a common power supply and the low battery signal is transmitted to an ESS control panel as a standard. The detector is equipped with two TAMPER contacts (front and rear), which immediately report opening of the detector cover or its possible tearing from the place of installation. The detector regularly performs automatic tests and reports its status via control transmissions to the system.

The PC-01 access card is a proximity card (RFID standard EM UNIQUE 125kHz). Up to 50 cards can be used in the system. For higher security each card can be combined with a digital code (PIN). It is possible to print your artwork on the card (using some computer printers).

The JA-86P is a component of Jablotron’s Oasis 80 alarm system. It is designed to detect human body movement inside buildings. Detection in two zones makes this detector more immune to moving pets. The battery-powered detector communicates via OASIS radio protocol.

The MCT-441 are fully supervised indoor, easy-to-install, PowerCode Gas detectors. The MCT-441 is a natural gas detector designed to send an alarm when Methane gas is detected. The detectors can be used in a house, apartment, caravan, mobile home or yacht.
The detectors are powered by 220 VAC. An internal Lithium battery is used for AC power failure reporting only (the battery does not power the detector).
The detector can send the following messages to the alarm system control panel: Gas alarm, gas sensor failure , AC power failure and low battery voltage.
The MCT-441 is designed for wall mounting and should be placed in a location where gas presence, for example leakage, is probable.
Upon gas detection, an audible buzzer is sounded and the built-in transmitter transmits a digital message, composed of the detector's PowerCode ID followed by status messages. Alarm and other data are thus forwarded to the alarm system. A periodic supervision message is transmitted automatically (see specifications) to inform the alarm system at regular intervals, of the unit’s active participation in the system.
The MCT-441 has a 24-bit ID code, randomly selected in the factory from over 16 million possible combinations. This code is therefore unique and virtually impossible to reproduce. Compatible PowerCode receivers are designed to "learn" specific IDs and respond only to them.

This P.I.R. motion detector is used to protect interiors. It detects any movement of objects with a temperature close to that of the human body.

Module of 8 wired inputs for JA-65K control panels.

The JA-82KRX is a configuration of the JA-82K control panel with the JA-82R 868MHz RF communications module and the JA-80X PSTN comunicator.
The JA 82K main board provides building-block-like modularity which allows functional extensions to be made by simply plugging-in the required modules.

Adds 8 outputs to the MCR-308 receiver. Up to 3 units can be added to each.

The PC-02 is the key tag version of the PC-01 card.

The MCT-550 is a fully supervised wireless flood detector compatible with PowerMax™ and other Visonic PowerCode™ wireless systems. It is designed to detect the presence of water in basements, yachts and many others residential and commercial applications, providing early warning of developing floods.
In default mode, the MCT-550 transmits each flood alert message a single time. However, users may program the detector to repeat the alert every three minutes until the device is reset.

The JA-80G detects mixtures of air and combustible gases or fumes (Natural Gas, Methane, Propane, Butane, Acetylene, GPL, Hydrogen, etc). The detector detects two levels of gas concentration, responding with two different reactions. The mains-powered detector indicates a gas leakage optically, and acoustically, and transmits alarm wirelessly via Oasis protocol.

MCR-308 is a superheterodyne receiver designed to convert a standard hard-wired control panel into a reliable fully supervised wireless system. It provides a cost-effective opportunity to realize all the benefits of Visonic wireless systems and devices.

MCR-308 is compatible with all Visonic PowerCode™ and CodeSecure™ devices – including hand-held and portable units, window/door transmitters and a variety of detectors and other devices. The MCR-308 has 4 zones, each accommodating up to 4 transmitter devices. It is easily expanded using up to three MCX-8 zone expanders, for a total of 28 zones and 112 wireless devices in a single system. Dry contact outputs can be provided, using the RL-8 relay module that converts 8 open collector outputs to dry contact outputs.

MCR-308 is designed for wireless alarm, emergency and arm/disarm applications as well as for remote control applications. It is easy to install and program utilizing a unique "Easy Learn" technique for transmitter enrolment. It provides all the features that professionals require, including four additional outputs for low battery reporting, tamper protection, RF signal jamming and transmitter inactivity indication.

When used with CodeSecure devices, the MCR-308 implements a rolling code encryption algorithm to prevent "code grabbing" by potential intruders trying to defeat the security system.

This highly reliable and versatile receiver is available in several optional frequencies in compliance with European, U.S. and other international standards, and is approved for use by local authorities in most countries.

The JS-25 COMBO is an outstanding "two in one" detector, which dramatically simplifies alarm installations.. This detector combines two sensors (P.I.R. motion & acoustic glass break) in one housing.

The JA-81E is a component of Jablotron’s OASiS alarm system and is designed to control and program the system. It has a built-in proximity access card reader and allows the wiring up of a separate door detector. The keypad should be wired to the control panel.

The JA-60WEB communicator is designed for JA-63 and JA-65 alarm control panels. The dialer is used for communication with a central monitoring station via an Ethernet network / the internet.

The JA-82KRC is a configuration of the JA-82K control panel that includes the JA-82R wireless communications module and the JA-82C wired inputs module. The JA 82K main board provides building-block-like modularity which allows functional extensions to be made by simply plugging-in the required modules.

TOWER®-20AM MCW is a ground-breaking anti-masking wireless mirror detector that provides unparalleled alarm detection in outdoor environments due to the unique patented technologies it employs. It is the first detector to prevent false alarms caused by outdoor interferences, such as rain, snow, lightning storms, swaying bushes, and free-roaming animals, while still providing reliable detection of real threats.
TOWER-20AM MCW features the revolutionary Octa-Quad™ technology, which uses eight PIR sensors (compared to only one used in other outdoor detectors), with each sensor acting as a Quad detector, to accurately determine whether an alarm is justified. In addition, further increasing its reliability, TOWER-20AM MCW also has a robust housing and patented anti-masking protection that can distinguish between masking spray, rain and sprinkler irrigation to provide exceptionally high resistance to vandalism and masking.

Usb cable with 1,6m, used to connect the PC to the iConnect, for programming.

The JA-83M is a component of Jablotron’s Oasis alarm system. It is designed to detect the opening of doors, windows etc. The battery-powered detector communicates via OASiS radio protocol.

The UC-82 is powered by an external 12V DC power supply and it provides 2 relays which can be controlled by radio signals and offers the following:

• Remotely controllable relay outputs which follow JA-80 control panel programmable PG outputs;
• Remote control of appliances using RC-8x controllers;
• Relay output of JA-8x wireless detectors;

MCX-610 extends the communication range between the PowerMax® systems and other PowerCode™ transmitter, including one-way and two-way keyfobs*, remote commander and PowerCode motion detectors. It receives alarm, status and control messages from the wireless devices, and sends these messages to the control panel.

For maximum security, the MCX-610 repeater uses a unique, factory programmed, randomly selected 24-bit digital alarm ID code during each transmission. This code is selected from 16 million possible code combinations and is therefore unique and virtually impossible to accidentally reproduce.

Other important benefits of the MCX-610 include the unique anti-collision transmission sequence, which ensures accurate reception of simultaneous signals from multiple transmitters. The fully supervised repeater issues a test report on an hourly basis, indicating faults such as power failure, low battery charge and tampering.

The Next Duo is a Dual Technology Digital Detector designed to prevent false alarms due to interferences in residential and light commercial environments. A passive infrared (PIR) sensor and a complementary active microwave sensor are combined in a single unit, giving Next Duo an unprecedented capacity to distinguish between the motion of a human body and any other disturbance.

The JA-82KR is a configuration of the JA-82K control panel with the JA-82R wireless communications module. The JA 82K main board provides building-block-like modularity which allows functional extensions to be made by simply plugging-in the required modules.

Jablotron JA-8X and JA-6X series control panels can be connected to a computer via the JA-80T interface cable. Connect the control panel’s external digital bus connector to the JA-80T interface input using a cable with suitable RJ connectors. Then plug the JA-80T’s USB plug into a free USB port on your PC. The correct drivers must be installed in to the computer to use the JA-80T. Once installed you can start using ComLink software - using this software the user/installer can easily program, operate, and test the system, read the latest events and much more.

The JA-81F is a component of Jablotron’s OASiS alarm system and is designed tocontrol and program the system. It has a built-in proximity access card reader andallows the wiring up of a separate door detector. The battery-powered keypad communicates wirelessly using OASiS protocol.

The JA-81M is a component of Jablotron’s Oasis 80 alarm system. It is designed to detect the opening of doors, windows etc. It can also be extended by a normally closed / normally open sensor.
It is also designed to detect the handling of roller blinds. This is achieved by detecting ratchet-wheel movements. Small movements are filtered out so that wind blasts do not cause false alarms.
The battery-powered detector communicates via OASIS radio protocol.

The TOWER 40 is a microprocessor-controlled wireless digital PIR detector, designed for easy installation, free of vertical adjustment. It features parabolic and cylindrical mirrors with uniform detection sensitivity throughout its operating range, up to 18 meters (59 ft), with creep zone protection.
The advanced True Motion Recognition™ algorithm (patented) allows the TOWER 40 to distinguish between true motion of an intruder and any other disturbances which may cause false alarms.
An on-board motion event jumper determines whether 1 or 2 consecutive motion events trigger an alarm.

AJAX ReX is a Range Extender that amplifies the wireless Jeweller signal coming from the AJAX Hub. By default, the AJAX Hub has a maximum transferable distance of 2000 meters, and with this ReX you extend the wireless signal by another 1800 meters. It will be clear that due to the enormous distance that is already achieved from the Hub, this Rex is only intended for homes with very large plots, or factories.

The MCR-304 superheterodyne receiver is designed for easy and cost-effective upgrading, enabling hard-wired control panels to operate with wireless remote devices. Compatible with all Visonic PowerCode™ and CodeSecure™ devices, the MCR-304 receiver supports up to 10 wireless devices – including hand-held and portable units, window/door transmitters and a variety of detectors and other devices. The MCR-304 is designed for wireless alarm, emergency and arm/disarm applications as well as for remote control systems and gate openers for garage and parking lots. It is easy to install and program utilizing a unique "Easy Learn" technique for transmitter enrolment. It provides all the features professionals require, including low battery reporting, tamper protection, RF signal jamming and transmitter inactivity output indication. When used with CodeSecure™ devices, the MCR-304 implements a rolling code encryption algorithm to prevent "code grabbing" by potential intruders trying to defeat the security system.

The JA-81E is a component of Jablotron’s OASiS alarm system and is designed to control and program the system. It has a built-in proximity access card reader and allows the wiring up of a separate door detector. The keypad should be wired to the control panel.

The UC-280 is an 8-zone interface linking JA-60 wireless detectors with hard-wired security control panels.

The JA-82M designed to detect opening windows, doors etc.

The MCT-560 is a fully supervised wireless PowerCode detector used with the PowerMax Pro (Ver. 5). The detector alerts the alarm system control panel upon detecting critical indoor or outdoor temperatures. The detector generates an alarm message when its sensor detects that the temperature has reached a certain temperature point. A restore message is generated when it crosses back the threshold temperature point. There are a total of four fixed temperature points and the user can enable one or more temperature point.
The MCT-560 can be used in instances where temperature detection is critical. Other examples of detector usage are as follows:

• Activating and deactivating pipe heaters at locations where low temperatures may causes the water in pipes to freeze.
• Warn of possible electrical device malfunction due to high or low temperature levels.
• Alerting elderly people of a significant rise or drop in room temperature.

The MCT-560 detects both indoor and outdoor temperatures. The detector monitors room temperature using an internal sensor. For outdoor or refrigerator installations, a waterproof temperature probe (optional) is used.
When the probe is connected, the temperature measurement is performed only by the probe sensor. When the probe is not connected, the temperature measurement is performed only by the detector's internal sensor.
Once the predefined temperature is reached, the detector wirelessly updates the alarm system control panel which then sends a notification to the central station or uses the PGM/X-10 controls to switch on a connected appliance, for example, a heater or air conditioner.

AJAX ReX is a Range Extender that amplifies the wireless Jeweller signal coming from the AJAX Hub. By default, the AJAX Hub has a maximum transferable distance of 2000 meters, and with this ReX you extend the wireless signal by another 1800 meters. It will be clear that due to the enormous distance that is already achieved from the Hub, this Rex is only intended for homes with very large plots, or factories.

Replacement NiMH battery pack for the Visonic Powermax Pro security console.

The JA-81F is a component of Jablotron’s OASiS alarm system and is designed to control and program the system. The display backlight colour can be set according to your needs.
It has a built-in proximity access card reader and allows the wiring up of a separate door detector. The battery-powered keypad communicates wirelessly using OASiS protocol.

The JA-84P provides human body movement detection including visual alarm verification.

Maintenance-free rechargeable lead-calcium batteries with 6V voltage and 1,3Ah capacity. This type of battery has a long lifetime and do not need any other care other than charging.

External antenna for the wireless equipment series Jablotron JA-60.

Replacement NiMH battery pack for the iConnect console.

The JA-80PB consists of two independent detectors which occupy two separate enrollment addresses in the control panel. The motion detector uses a PIR sensor. The glass-break detector uses the analysis of air pressure variations combined with the characteristic sound of glass breaking. The product is designed for internal use in buildings. The battery-powered detector communicates via OASIS radio protocol.

The MT-77 Piccolo terminal is a communication accessory for Jablotron home system. It should be connected to JA-6x control panel equipped with GSM communicator.

The GBS-210 glass break detector detects the breaking of glass windows.

The JA-89P is an outdoor intruder detector designed to detect human body movement in a protected area. It supplements a double-zone PIR sensor produced by Optex with a Jablotron transmitter enabling the sensor to be used within JA-80 OASiS systems.

Lithium battery for MCS-710 and MCS-730 wireless sirens.

Magnetic door sensor Normaly closed contact

The JA-80P is designed to detect human body movement inside buildings. The detection pattern can be modified by optional lenses. Detector immunity has two selectable levels. The battery-powered detector communicates via OASIS radio protocol.

Magnetic door sensor Normaly closed contact

This new compact PIR detector is available giving great performance and less visual impact. It works with Jablotron’s OASiS alarm system. It is designed to detect human body movement over 112 m ² of floor space inside buildings.
The detection pattern can be modified by optional lenses to be pet-immune. Detector immunity has two selectable levels. The detector communicates via OASIS radio protocol runs on battery power.

37cm antenna with magnetic base for Jablotron JA-60GSM dialer.

The GS-133 detects all mixtures of air and combustible gas (Natural Gas, Methane, Propane, Butane, Acetylene, GPL, etc). The detector detects two levels of gas concentration - with corresponding output reactions.
The main GS-133 features are: high reliability and sensitivity, compact size and long stability & lifetime.

Detects shock and tilt on doors, windows etc. caused by an intruders attempts to force, smash, drill, or saw through. Has easy installation and uses digital signal processing. Features a memory of previous shocks.
The detector is a component of the JABLOTRON ALARMS Oasis security system. It has two selectable operation modes. The mode for the detection of shocks / vibrations of doors, windows, etc. can be used to indicate attempts to breach these by force.
The tilt detection mode can be used to indicate unwanted tampering with the object to which the detector is firmly fixed. This may be used for safes, artworks etc.
The detector uses a semiconductor tri-axial accelerometer with digital output. Its signal processing guarantees a high immunity against false alarms.
The detector communicates wirelessly using Oasis protocol and it is battery powered.

The detector is intended to detect human body movement in buildings. Using two sensors ensures better immunity against triggering by moving pets.
The signal is processed by a multiple signal analysis method which guarantees excellent sensitivity and a high resistance to false alarms. Detection analysis can be adjusted to increase its immunity (if installed in a problematic location). The detector distinguishes itself with excellent immunity against high frequency interference and other false signals. It can be installed on a flat wall or in a corner.

External antenna for the wireless equipment series Jablotron JA-60.

ABS back and front box in grey color. Front and back finishing acessories in glossy black acrylic. This service is an add-on to the iConnect control system you acquired.

FEATURES: - 50mm magnet clearance - Adjustable aluminum bracket - Material: The. Cast Zinc Contact Encapsulation B. ABS magnet encapsulation C. Aluminum alloy L-bracket - Shielded cable with lengths and 61 cm - High quality reed and magnet switch - Gray color

Maintenance-free rechargeable lead-calcium batteries with 12V voltage and 2,2Ah capacity. This type of battery has a long lifetime and do not need any other care other than charging.