Interface GSM

This kit adds the indoor wireless siren EWS1 to the security sensor EPIRw.
In case of alarm the system can send warnings via SMS or voice call and warn the people around with the siren.

ET08 provides a "dial tone" and fully replaces a telephone landline for Alarm Control Panel reporting to the central monitoring station when telephone line is unavailable or has been cut or disconnected by PSTN provider. Can detect temporary service suspension by the service provider for technical or billing reasons even if a "dial tone" is still present. (optional extra)

The motion detector operates very simply: it responds to human movements within protected area and informs the owner about this by calling mobile phone and sending SMS.
From the technical viewpoint, this facility is an infrared volume announcer combined with GSM-communicator, built-in radio module allows to operate with remote controllers (turn on/off the protection mode).
A number of patented knowledge, protected by the law of copyright, was employed at motion detector "EXPRESS GSM".
GSM motion detector is supplied with power by Li-battery CR123 (3V). The manufacturer guarantees not less than 6 months of continuous operating with the same battery.
Advanced options For those who want to make customs settings, there is such a possibility. There are many options to set up:

• additional phone numbers for warning (up to 6 numbers);
• additional remote controllers (up to 6 pieces) ;
• warning method: call+SMS or only SMS. The first method is preferred as it is less probable to miss incoming call than SMS;
• frequency of test messages and messages of balance. motion detector sends test messages to owner’s mobile phone with some frequency. They contain the information about signal strength and temperature of GSM-module, SIM-card balance. On default messages are sent once a week. It is possible to set up how often the messages of balance will be sent (along with every standard test message, along with every second, third, tenth etc. test message);
• temporary delay of turning on the protection mode, of warning call;
• time for automatic returning to protection mode after alarm. In case of false alarm motion detector will continue to protect the object and will not disturb the owner. In case of real entry, alarm messages will be sending continuously if trespasser hasn’t left;

By plugging the GD-04R radio module into the digital bus connector your David acquires the following capabilities:

• Relay X and Y state transmission to UC or AC OASiS wireless receivers.
• Input A to D activations via RC-8x OASiS wireless buttons or via JA-8x OASiS wireless detectors.
• Relay X or Y control via RC-8x OASiS wireless buttons.
• Relay X or Y control via a TP-8x wireless thermostat.

The module has a built-in internal antenna. If necessary, a Jablotron external antenna of type AN-80 or AN-81 can be applied to extend David’s working range.

ESIM251 is a microcontroller based device used to inform users about the alarm in automatic or security systems and control one electric appliance -relay.

Alarm and control system ESIM251 works over GSM network.

It works 24/7, it always reacts to the incoming signal.

ESIM251 can control 1 electronic appliance (a relay) sending a password and a special command from a GSM phone of any of the users. You can, for example, turn on the heating, lighting, lift the gates, blinds etc.

The system will ignore requests coming from unknown telephone number or SMS message with wrong password.

Indoor wireless sirens EWS1 is a wireless device with integrated siren speakers which are used for operating ELDES wireless security systems. Users have to bind it to the central device of security system (by sending a corresponding command via SMS message or using software "ELDES Configuration Tool“). Connected devices are recognized as central security system devices and can be controlled via system phone number. The system adds one wireless zone and one wireless output. Wireless zone is used to monitor device and wireless output is used to control the speaker. When the system is violated, the siren alarms for one minute. It is possible to connect up to 16 wireless devices to the central security system at a time.

A GD-04P link cable, which allows you to connect David to a PC through a USB port and perform any desired configuration using GDLink software.

This module is imbedded in a specially-enlarged replacement cover. Installation is performed by replacing the original cover, together with wiring the GD-04A module to the GD-04 circuit board via the corresponding connector.
The backup battery requires approx. 72 hours to be fully charged. The battery provides approx. 12 to 24 hours of backup operation, depending on the output relay state and on the GSM signal strength (as with any GSM device, David’s consumption is higher in places with a low signal level as the transmitter power has to be increased).

ESIM010 is a microcontroller based device used to control gate automatics, road barriers or to remotely turn on the electronic device over GSM network.

Magnetic door contact with panic button EWD1 is a wireless device with magnetic contact which are used to secure doors, windows or any other opening parts and operating with ELDES wireless security systems. Users have to bind it to the central device of security system (by sending a corresponding command via SMS message or using software „ELDES Configuration Tool“). When EWD1 is connected to the system, two wireless zones are added. First wireless zone is used to monitor the magnetic contacts and the second wireless zone is for managing the panic button. By default panic button zone is configured as Silent zone and in case of violation, system will cause an alarm to administrator numbers or/and to monitoring station without turning the siren on. It is possible to connect up to 16 wireless devices to the central security system at a time. Maximum distance for wireless connection is 150 meters (in open areas).

The GD-04 David is a universal GSM dialer and controller. DAViD provides 2 output contacts of power relays and 4 input terminals. The GD-04 can be easily set up by using the configuration web page.

Alarm and control system ESIM021 is used to inform a maximum of two users through the GSM network that an alarm has occurred. Users may also control one electrical device via their mobile phones, e.g. they may switch a lighting system on and off or open and close a gate.

ESIM021 may be connected to an intruder alarm control panel. It has two digital inputs (normally open), so that one detection device may be connected independently of the intruder alarm control panel, or alternatively two detection devices may be connected to ESIM021 without needing a control panel.

When a triggered zone is restored to pre-alarm, the system also sends an SMS or voice message confirming that this has been done.

Either user may turn the heating or lighting on or off, open gates, lift blinds etc. by sending ESIM021 a text message. Only one electrical device may be controlled in this way. The system remembers the status of output in the case of temporary electricity failures. The system will ignore requests and calls coming from unknown telephone numbers.

Outdoor wireless siren EWS2 is external power supplied siren with integrated wireless module EW1. This wireless module EW1 connects to ELDES wireless security systems and managing EWS2 siren to work with the system. Users have to bind it to the central device of security system (by sending a corresponding command via SMS message or using software „ELDES Configuration Tool“) and configure input zones and outputs. Connected devices are recognized as central security system devices and can be controlled via system phone number. The siren has integrated battery and in case of power supply failure, it starts alarming. When the system is violated, the siren alarms for one minute. EW1 module also has one unused zone and one unused output. They can be used to connect variuos additional devices such as motion sensors, smoke detectors and etc (see wireless expansion module EW1 manual).

The GD-04D allows relay X and Y control by entering numeric codes (DTMF codes) on the telephone keypad during calls. The DTMF codes intended for use have to be programmed.

ESIM264 is an Alarm and Control System (GSM Caller) for the security of premises and control or management of electronic devices through GSM network. The basic advantage of the GSM system is the user’s ability to know immediately what’s happening at their home, apartment, warehouse, summer house or other premises even when the user himself is a long way away – in another city or even in another country. It also has a remote control switch to turn on or turn off 4 or more different devices just by sending SMS messages.

• System can be armed and disarmed in one of three ways: via keypad EKB3, key iButton® or free-of-chage call from your phone;
• ESIM264 supports the CONTACT ID protocol which is required to transmit signals to a Monitoring Station;
• ELDES wireless devices can be added to the system using the EWT1 module. This increases the maximum number of Zones to 44 units and the maximum number of Outputs to 44 units;
• Automatic Output control – the system may enable / disable individual Outputs automatically when a specified event occurs;
• Fault reporting: The system automatically reports if any of the sensors or sirens disconnect from the system;
• Battery check option - checks the health of the battery and reports when the battery needs to be replaced;

PIR sensor EWP1 is a wireless device with integrated motion detector for use as part of the ELDES wireless security system. The sensor allow expanding security zones administrated by the systems up to 16 additional zones and also the installation is comfortable and simple as it does not require any wired connections between the system devices. The user only needs to turn on the required number of PIR sensors EWP1 and connect them to the control panel, either by sending a command via SMS message or using the ELDES Configuration Tool software.

EPIR is a security alarm system that works with GSM network.

Alarm system ELDES EPIR supports CONTACT ID protocol which is required to transmit signals to Monitoring station.

ELDES EPIR868 (ELDES EPIR version with installed 868 MHz radio transmitter-receiver) can operate as an access point for wireless ELDES devices.

The system DZEUS is a micro-processor device used to remotely observe and control cars, motorbikes and other vehicles through GSM network.

EPIR is a security alarm system that works with GSM network.